• Home
  • >
  • Our Blog
  • >
  • Common Problems with Transfer Tape and How to Fix Them

Common Problems with Transfer Tape and How to Fix Them

transfer paper for cricut

Every craft designer looks forward to seeing their designs on their final project because that is where the beauty of their hard work is best expressed. Transfer tape is one of the surest ways of getting over the line of work to completion. However, your expectation may turn into chaos if a few anything goes wrong. This could be frustrating for many craft designers, especially for beginners. 

So, what could go wrong when using the adhesive transfer tape? How do I fix these problems? How to use cricut transfer tape? These questions and many others may cause you some worries. Here are some quick tips to help.

Top Problems with Transfer Tape and Its Solution

1. Stickiness. One common problem you may have when using a vinyl transfer paper for cricut is related to the adhesive tackiness. If the sticky tackiness is too low, your vinyl design won't leave it packing paper. If vinyl not sticking to transfer tape or vinyl won't stick to transfer tape, the beauty of finished handicrafts will be affected. Besides, if the adhesive tackiness is too high, your vinyl design won’t leave the tape and stick to your final project. So, cricut transfer tape too sticky doesn't work either.

HTVRONT Transfer Type

To fix these problems, you may need to buy another adhesive transfer tape that has a moderate adhesive tackiness. So check for the best before you buy transfer paper for cricut. However, it is better to reuse a clear vinyl transfer tape just once to avoid these kinds of problems. If the adhesive tackiness of your clear vinyl transfer tape is too high, you can place the transfer paper for cricut on other surfaces like blankets, denim, or jeans. The fuzziness of these materials will reduce the adhesive tackiness of the transfer tape, and you can reuse the same transfer tape for subsequent projects. 

2. Cutting. Furthermore, you could also have problems with your cuttings. This could make it challenging to take out your vinyl design for transfer. When you make deep cuts on your vinyl decals, you may also cut their packing paper. When you place your adhesive transfer tape on these rooted cuttings, it may require some force to peel-out your design. This may cause your design to appear like patches with varying degrees of distortion.

To fix these problems, flip your vinyl decal after placing the tape on it. Then peel out the light packing paper from the deep cut. However, to prevent this problem from reoccurring, adjust the settings of your vinyl decal, and always lighten the pressure you place on your cutter when cutting your vinyl decal.

3. Material residues. Another problem with using clear vinyl transfer tape is the inability of your vinyl design to stick to your final project. This is mostly due to residues from either your hand or the manufacturer of your project material that is incompatible with your adhesive transfer tape whether the material is glass, metal, textile, or wood. 

HTVRONT Transfer Tape

To fix this, it is advisable that you wash your hands, and allow it to air dry before doing your transfer. You should also clean your project surface thoroughly with alcohol or nail varnish. If your project is a wood surface, you should smooth it with sandpaper, or apply a paint layer. You can also use heat when doing your transfer to help your design stick to your final project.

4. Adhesive Usage. Finally, sometimes the challenge could be with your adhesive transfer tape. The adhesive used may require some time to stick to your final project. All you need to do is to place your adhesive transfer tape with the design on the surface of your final project and allow it for about 15-20 minutes before taking off the vinyl tape.

Challenges and mistakes are inevitable in every human endeavor, including craft designing. Besides, errors can be easily corrected. Using the few quick tips discussed here will help you spend less time on your crafts, and enjoy more fulfillment. 


Tips and Tricks on How to Use Transfer Tape

If you want to know more about how to use transfer tape, detailed steps can be found in this blog: A Step-by-step Guide on How to Use Transfer Tape. Here, some tips and tricks to apply transfer tape are listed below:

Avoiding removing all transfer tapes at one time is recommended. It means that when you are unsure about which transfer decal needs to be placed, there is a need for you to take all of the backing transfer tape off for some time. At the very beginning, you just need to peel a corner off, enabling it to be onto the part of the substrate what you want. In this sense, you are able to boast an panorama of .the overall shape and design. Only by doing so, the rest of the tape can be removed with no errors.

HTVRONT Transfer Tape

You should leave more room for the transfer tape than for the vinyl. If the transfer tape is smaller than the vinyl, it will lead to the potential risks of repeating completing previous works. On the contrary, even though you have do something wrong, there still boast some room for adjustment and optimization.

The transfer tape should not be cut on the flat surface. If you are new to use the transfer tape, the tape may be embedded with some wrinkles in the items. As a result, you should snip a little bit of the transfer tape to allow the material to become flexible. And an excellent work can be shown to you. 


Tips for Applying Adhesive Vinyl

To help you make perfect craft projects every time, here are some tips about applying adhesive vinyl:


  • No matter what surface you are using, always make sure to clean it properly and let it dry.
  • Just before applying the vinyl, wipe a little with a dry cloth. This will help remove all the dust and make the dust clean.
  • If you are using a new material, please make a small test piece first. You don't need to print the entire vinyl but just use a small part to test.
HTVRONT Adhesive Vinyl

What does Adhesive Vinyl not Stick to?

Fabrics. There is no easy way to use adhesive vinyl to the fabric. Vinyl may fall off during the washing process. If it is used on clothes, it is easy to loosen the vinyl by constant movement while wearing them. It's recommended to use heat transfer vinyl to fabric, after all. 

share :

Please note, comments must be approved before they are published